Uso da biodiversidade por populações humanas na caatinga e na Mata Atlântica, Rio Grande do Norte, Nordeste do Brasil

The use of animals is a common activity but it can be really variable between human populations. This work analyzed the knowledge about useful animal species between human communities in Caatinga and Atlantic Forest considering the influence of socioeconomics and environmental factors on the species selection. Forty people were interviewed in Caraúbas community (Atlantic Forest) and thirty were interviewed in Barrocas community (Caatinga). A total of 193 animals were cited. The communities showed a low degree of similarity (20%) and the general diversity of mentioned species was significantly bigger in Caraúbas. Men cited a diversity of species greater than women for food category in Caraúbas and pet category in Caraúbas and Barrocas. Women cited greater species diversity for medicinal use in Caraúbas. In general, in both communities, the age group >60 years showed a greater knowledge than the others. The multiple regression analysis showed the age as the only socioeconomic factor which influenced significantly the knowledge about animals for the food category in both communities. Considering the richness of known species, there were differences only between gender for sum of uses and food category in Caraúbas and for the pet category in Barrocas with men showing a greater knowledge than women. The results showed that local environmental differences are fundamental at the species selection but they also showed that within communities there are other factors like gender and age that tend to influence the knowledge about species. It is important to consider cultural, economic, social and environmental factors to understand better the interactions between people and animals so that this information can be used to facilitate the implementation of conservation measures

Mapeamento da zona costeria protegida por arenitos de praia (Beachrocks) em Nísia Floresta - RN

The goal of this work comprises the detailed mapping of the coastal zone of the south coast of the State of Rio Grande do Norte. The emphasis of the study is the units of beachrocks and the features of the physical environment associated. The mapping of the beachrocks and of the adjacent coastal features is justified, among other aspects, by the fact that the beachrocks constitute an important protection agent against the sea erosion. By one side, they dissipate the energy of the sea waves and make possible the imprisonment of sediments in the foreshore. The beachrocks in the studied area are constituted of discontinuous strips, parallel to the coast line presenting emerged in some places, even in the highest tides, entirely submerged or partially buried by coastal sediments. These sandstones compose the landscape of big part of the coast and they are responsible for the partial dissipation of the energy of the waves on the studied coast. The methodology used in this work consisted of different techniques were used, as the use of aerial pictures of small format (FAPEFs), acquisition of data of system of global positioning (GPS) and later elaboration of thematic maps and of digital models of soil (MDTs). The results obtained in the mapping of the use and occupation of the soil, demonstrate the existence of strong human pressure in the coastal area (built lots and no built), occupying about 54,74% of built areas. This problem has been taking to degradation risks due to the inconsequent expansion of divisions into lots and tourist enterprises. The MDT came as an excellent resource, as visual as functional, being possible to visualize several angles and to act in three dimensions the relief of the area in study, as well as to identify the present features in the coastal area. By the importance of the bodies of beachrocks as a protection agent against the coastal erosion, faces were delimited in the sandstones based in geometric criteria, classifying them in, central face, outside face, inside face, break and undermiming. These last two associates to the erosion and washout in the base of these bodies. Field data indicate clearly that the most important process in the fracturing of the bodies is associated with mechanisms related to the gravity, being the joints formed by processes of gravitational sliding. Finally, the mapping of the coastal zone starting from aerial pictures of small format it made possible the identification of the elements that compose the beach strip, for accomplishing with larger detailed level and by presenting a better monitoring of the dynamics of the coastal zone

Avaliação do efeito do liraglutida nos tecidos muscular e adiposo e nos parâmetros bioquímicos em camundongos Swiss submetidos à dieta de cafeteria e a atividade física

Obesity is a chronic metabolic disease characterized by adipose tissue formation excess leading to an increase in body fat mass, of multifactorial origin, produced mainly by poor eating habits combined with a sedentary lifestyle. Data consider obesity as a serious disease that affects the world's population, ranking fifth in death rates. Faced with this situation, individuals seek, increasingly, means to lose weight with less physical effort and food. In 2009 and 2010 the drug liraglutide was lauched in order to reduce weight in individuals with diabetes mellitus type 2, thus avoiding the emergence of other diseases. The aggravating factor is that obese nondiabetic individuals are making use of this substance, even if its use is not authorized by ANVISA (Brazilian Health Surveillance Agency). Thus the objective of this research is to evaluate the effect of liraglutide for muscle or fat tissues and biochemical parameters in Swiss mice submitted to cafeteria diet and physical activity. The study was approved by the Ethics Committee on Animal Use - CEUA (nº003 Protocol / 2014). For this study 74 animals (Swiss mice) were used, divided as follows: in the initial phase of this study, we carried out a pilot study (n = 10) divided into a control group (PCON) (n = 5) and cafeteria group (PCAF) (n = 5), in order to evaluate a cafeteria diet which was both attractive to the animals and that could provide an increase in adipose tissue. After the induction of the diet, animals were euthanized and as a result, the animals in the PCAF group showed an intra-abdominal adiposity 0.74 ± 0.05 g, taken as the parameter for increasing fat in animals. Subsequently the study base was conducted for this research where animals were used (n = 64) divided into 2 groups: the Cafeteria Study Base Group (EBCAF) divided as follows: cafeteria + exercise + liraglutide (CEL) (n = 8), cafeteria + exercise + saline (CES) (n = 8), cafeteria + liraglutide (CL) (n = 8) and cafeteria + saline (CS) (n = 8). The Chow Study Base group (EBR) was divided into: exercise + liraglutide (EL) (n = 8), exercise + saline + (ES) (n = 8), liraglutide (L) (n = 8) and saline solution (SS) (n = 8). All animals went through the submission process to the cafeteria diet, followed by exercise protocol through swimming and treatment with the test substance intraperitoneally (200 mg / mL / kg). After the treatments, the animals were euthanized and had the following parameters evaluated: the muscle tissue mass, adipose tissue mass and biochemical parameters. It was observed that the processing done with the exercise-associated liraglutide reduced adipose tissue mass significantly (0.32 ± 0.05 g) compared to the saline group (0.53 ± 0.07 g). There were no changes in the muscle tissue of the group which was treated and exercised (1.39 ± 0.03 g) compared to the saline group (1.33 ± 0.03 g). Regarding biochemical parameters it was evident that there were changes in these parameters. Interesting to note that, although blood glucose values have been changed, the animals did not become diabetic. Thus, it appears that physical activity together with liraglutide is eficcient to the loss of intraabdominal adipose tissue and the maintenance of lean body mass thereby generating a satisfactory result in the pursuit of quality of life and disease prevention.

Avaliação do efeito do liraglutida nos tecidos muscular e adiposo e nos parâmetros bioquímicos em camundongos Swiss submetidos à dieta de cafeteria e a atividade física

Obesity is a chronic metabolic disease characterized by adipose tissue formation excess leading to an increase in body fat mass, of multifactorial origin, produced mainly by poor eating habits combined with a sedentary lifestyle. Data consider obesity as a serious disease that affects the world's population, ranking fifth in death rates. Faced with this situation, individuals seek, increasingly, means to lose weight with less physical effort and food. In 2009 and 2010 the drug liraglutide was lauched in order to reduce weight in individuals with diabetes mellitus type 2, thus avoiding the emergence of other diseases. The aggravating factor is that obese nondiabetic individuals are making use of this substance, even if its use is not authorized by ANVISA (Brazilian Health Surveillance Agency). Thus the objective of this research is to evaluate the effect of liraglutide for muscle or fat tissues and biochemical parameters in Swiss mice submitted to cafeteria diet and physical activity. The study was approved by the Ethics Committee on Animal Use - CEUA (nº003 Protocol / 2014). For this study 74 animals (Swiss mice) were used, divided as follows: in the initial phase of this study, we carried out a pilot study (n = 10) divided into a control group (PCON) (n = 5) and cafeteria group (PCAF) (n = 5), in order to evaluate a cafeteria diet which was both attractive to the animals and that could provide an increase in adipose tissue. After the induction of the diet, animals were euthanized and as a result, the animals in the PCAF group showed an intra-abdominal adiposity 0.74 ± 0.05 g, taken as the parameter for increasing fat in animals. Subsequently the study base was conducted for this research where animals were used (n = 64) divided into 2 groups: the Cafeteria Study Base Group (EBCAF) divided as follows: cafeteria + exercise + liraglutide (CEL) (n = 8), cafeteria + exercise + saline (CES) (n = 8), cafeteria + liraglutide (CL) (n = 8) and cafeteria + saline (CS) (n = 8). The Chow Study Base group (EBR) was divided into: exercise + liraglutide (EL) (n = 8), exercise + saline + (ES) (n = 8), liraglutide (L) (n = 8) and saline solution (SS) (n = 8). All animals went through the submission process to the cafeteria diet, followed by exercise protocol through swimming and treatment with the test substance intraperitoneally (200 mg / mL / kg). After the treatments, the animals were euthanized and had the following parameters evaluated: the muscle tissue mass, adipose tissue mass and biochemical parameters. It was observed that the processing done with the exercise-associated liraglutide reduced adipose tissue mass significantly (0.32 ± 0.05 g) compared to the saline group (0.53 ± 0.07 g). There were no changes in the muscle tissue of the group which was treated and exercised (1.39 ± 0.03 g) compared to the saline group (1.33 ± 0.03 g). Regarding biochemical parameters it was evident that there were changes in these parameters. Interesting to note that, although blood glucose values have been changed, the animals did not become diabetic. Thus, it appears that physical activity together with liraglutide is eficcient to the loss of intraabdominal adipose tissue and the maintenance of lean body mass thereby generating a satisfactory result in the pursuit of quality of life and disease prevention.

Modelo de classificação para pequenas empresas supermercadistas quanto ao uso de técnicas de prevenção de perdas: um estudo de caso

The objective of this work is to draw attention to the importance of use of techniques of loss prevention in small retail organization, analyzing and creating a classification model related to the use of these in companies. This work identifies the fragilities and virtues of companies and classifies them relating the use of techniques of loss prevention. The used methodology is based in a revision of the available literature on measurements and techniques of loss prevention, analyzing the processes that techniques needed to be adopted to reduce losses, approaching the "pillars" of loss prevention, the cycle life of products in retail and cycles of continues improvement in business. Based on the objectives of this work and on the light of researched techniques, was defined the case study, developed from a questionnaire application and the researcher's observation on a net of 16 small supermarkets. From those studies a model of classification of companies was created. The practical implications of this work are useful to point mistakes in retail administration that can become losses, reducing the profitability of companies or even making them impracticable. The academic contribution of this study is a proposal of an unpublished model of classification for small supermarkets based on the use of techniques of loss prevention. As a result of the research, 14 companies were classified as Companies with Minimum Use of Loss Prevention Techniques - CMULPT, and 02 companies were classified as Companies with Deficient Use of Loss Prevention Techniques - CDULPT. The result of the research concludes that on average the group was classified as being Companies with Minimum Use of Techniques of Prevention of Losses EUMTPP, and that the companies should adopt a program of loss prevention focusing in the identification and quantification of losses and in a implantation of a culture of loss prevention

Fatores inibidores do uso de técnicas ambientais nos postos de combustíveis: um estudo de caso em Natal/RN

The objective of this work was to investigate the factors that inhibit the use of Environmental Techniques in the Gas Station of the city of Natal/RN. For this, a survey with the aid of a questionnaire was used like research instrument. It s used a sample for convenience, not probabilistic. For collection of the data, it was used directly application of the questionnaire to the Managers or Assistant managers of the gas station, in accordance with its availability or presence. The data was collected in all the regions of Natal (North, South, East and West). The population in accordance with the data of the ANP of September 2005 is of 111 ranks and the collected sample was of 86. To carry through the analysis of the data of this research had been used softwares Excel and Statistic version 5.0, for Windows. The analysis of data is divided in two parts; descriptive analysis and analysis of groupings (clusters). The results showed that bigger part of the interviewed ones has between 30 and 39 years of age; they have second grade completed; they had declared to have little between and reasonable knowledge how much to the use of Clean Technology (CT) in gas station; and a small part of the interviewed ones had informed to have much knowledge how much the resolutions of the CONAMA established for the Gas Station. Of the searched ranks, the majority is national(76.7%); the most accurate practice environmental used in the gas station are: it collects selective of oil used or contaminated and ecological tanks - coated with strengthened fibre glass; great part of the interviewed ones (33.8%) informed that never the TL makes planning of referring future action; about of the half of the interviewed ones (84.9%) they had more declared that its employees have of none to a reasonable level of training for deal with problems that compromise the environment; the majority of the ranks (72.1%) functions has for more then six years. It is observed that almost all the interviewed ones (96.5%) evaluate as being important or very important the implantation of CT in Gas Station and the great majority (82.1%) evaluates the difficulty in if implanting these technologies in Gas Station as being easy or very easy. In the analysis of cluster, it was verified existence of two groupings (as much in the variable of the barriers and benefits), being that inside of each clusters exists homogeneity and between clusters exists heterogeneity. In reality, everything is important or very important in the opinion of the interviewed ones. There only exists a small significant difference that separates them in clusters

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developing the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. It s important to point out that, in spite of the loads being normally connected to the transformer s secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Uso de técnicas de otimização baseadas em derivadas como suporte do planejamento operacional de redes de distribuição de energia elétrica

The usual programs for load flow calculation were in general developped aiming the simulation of electric energy transmission, subtransmission and distribution systems. However, the mathematical methods and algorithms used by the formulations were based, in majority, just on the characteristics of the transmittion systems, which were the main concern focus of engineers and researchers. Though, the physical characteristics of these systems are quite different from the distribution ones. In the transmission systems, the voltage levels are high and the lines are generally very long. These aspects contribute the capacitive and inductive effects that appear in the system to have a considerable influence in the values of the interest quantities, reason why they should be taken into consideration. Still in the transmission systems, the loads have a macro nature, as for example, cities, neiborhoods, or big industries. These loads are, generally, practically balanced, what reduces the necessity of utilization of three-phase methodology for the load flow calculation. Distribution systems, on the other hand, present different characteristics: the voltage levels are small in comparison to the transmission ones. This almost annul the capacitive effects of the lines. The loads are, in this case, transformers, in whose secondaries are connected small consumers, in a sort of times, mono-phase ones, so that the probability of finding an unbalanced circuit is high. This way, the utilization of three-phase methodologies assumes an important dimension. Besides, equipments like voltage regulators, that use simultaneously the concepts of phase and line voltage in their functioning, need a three-phase methodology, in order to allow the simulation of their real behavior. For the exposed reasons, initially was developped, in the scope of this work, a method for three-phase load flow calculation in order to simulate the steady-state behaviour of distribution systems. Aiming to achieve this goal, the Power Summation Algorithm was used, as a base for developping the three phase method. This algorithm was already widely tested and approved by researchers and engineers in the simulation of radial electric energy distribution systems, mainly for single-phase representation. By our formulation, lines are modeled in three-phase circuits, considering the magnetic coupling between the phases; but the earth effect is considered through the Carson reduction. Its important to point out that, in spite of the loads being normally connected to the transformers secondaries, was considered the hypothesis of existence of star or delta loads connected to the primary circuit. To perform the simulation of voltage regulators, a new model was utilized, allowing the simulation of various types of configurations, according to their real functioning. Finally, was considered the possibility of representation of switches with current measuring in various points of the feeder. The loads are adjusted during the iteractive process, in order to match the current in each switch, converging to the measured value specified by the input data. In a second stage of the work, sensibility parameters were derived taking as base the described load flow, with the objective of suporting further optimization processes. This parameters are found by calculating of the partial derivatives of a variable in respect to another, in general, voltages, losses and reactive powers. After describing the calculation of the sensibility parameters, the Gradient Method was presented, using these parameters to optimize an objective function, that will be defined for each type of study. The first one refers to the reduction of technical losses in a medium voltage feeder, through the installation of capacitor banks; the second one refers to the problem of correction of voltage profile, through the instalation of capacitor banks or voltage regulators. In case of the losses reduction will be considered, as objective function, the sum of the losses in all the parts of the system. To the correction of the voltage profile, the objective function will be the sum of the square voltage deviations in each node, in respect to the rated voltage. In the end of the work, results of application of the described methods in some feeders are presented, aiming to give insight about their performance and acuity

Uso de técnicas de Geoprocessamento e Sensoriamento Remoto no levantamento e integração de dados necessários a gestão ambiental dos campos de extração de óleo e gás do Canto do Amaro e Alto da Pedra no município de Mossoró - RN

The objective of this work is to identify, to chart and to explain the evolution of the soil occupation and the envirionment vulnerability of the areas of Canto do Amaro and Alto da Pedra, in the city of Mossoró-RN, having as base analyzes it multiweather of images of orbital remote sensors, the accomplishment of extensive integrated works of field to a Geographic Information System (GIS). With the use of inserted techniques of it analyzes space inserted in a (GIS), and related with the interpretation and analyzes of products that comes from the Remote Sensoriamento (RS.), make possible resulted significant to reach the objectives of this works. Having as support for the management of the information, the data set gotten of the most varied sources and stored in digital environment, it comes to constitute the geographic data base of this research. The previous knowledge of the spectral behavior of the natural or artificial targets, and the use of algorithms of Processing of Digital images (DIP), it facilitates the interpretation task sufficiently and searchs of new information on the spectral level. Use as background these data, was generated a varied thematic cartography was: Maps of Geology, Geomorfológicals Units soils, Vegetation and Use and Occupation of the soil. The crossing in environment SIG, of the above-mentioned maps, generated the maps of Natural and Vulnerability envirionmental of the petroliferous fields of I Canto do Amaro and Alto da Pedra-RN, working in an ambient centered in the management of waters and solid residuos, as well as the analysis of the spatial data, making possible then a more complex analysis of the studied area

Uso da espectroscopia do infravermelho próximo e técnicas multivariadas para diferenciar escherichia coli e salmonella enteritidis inoculadas em polpa de fruta (abacaxi)

Aiming to consumer s safety the presence of pathogenic contaminants in foods must be monitored because they are responsible for foodborne outbreaks that depending on the level of contamination can ultimately cause the death of those who consume them. In industry is necessary that this identification be fast and profitable. This study shows the utility and application of near-infrared (NIR) transflectance spectroscopy as an alternative method for the identification and classification of Escherichia coli and Salmonella Enteritidis in commercial fruit pulp (pineapple). Principal Component Analysis (PCA), Independent Modeling of Class Analogy (SIMCA) and Discriminant Analysis Partial Least Squares (PLS-DA) were used in the analysis. It was not possible to obtain total separation between samples using PCA and SIMCA. The PLS-DA showed good performance in prediction capacity reaching 87.5% for E. coli and 88.3% for S. Enteritides, respectively. The best models were obtained for the PLS-DA with second derivative spectra treated with a sensitivity and specificity of 0.87 and 0.83, respectively. These results suggest that the NIR spectroscopy and PLS-DA can be used to discriminate and detect bacteria in the fruit pulp

A satisfação e a intenção de continuidade de uso em servços de e-learning:validação empírica de um modelo aplicado no serviço público

The present study aims to investigate the constructs of Technological Readiness Index (TRI) and the Expectancy Disconfirmation Theory (EDT) as determinants of satisfaction and continuance intention use in e-learning services. Is proposed a theoretical model that seeks to measure the phenomenon suited to the needs of public organizations that offer distance learning course with the use of virtual platforms for employees. The research was conducted from a quantitative analytical approach, via online survey in a sample of 343 employees of 2 public organizations in RN who have had e-learning experience. The strategy of data analysis used multivariate analysis techniques, including structural equation modeling (SEM), operationalized by AMOS© software. The results showed that quality, quality disconfirmation, value and value disconfirmation positively impact on satisfaction, as well as disconfirmation usability, innovativeness and optimism. Likewise, satisfaction proved to be decisive for the purpose of continuance intention use. In addition, technological readiness and performance are strongly related. Based on the structural model found by the study, public organizations can implement e-learning services for employees focusing on improving learning and improving skills practiced in the organizational environment

Relações entre perfil de valores e perfil de uso da tecnologia: Um estudo com os docentes que atuam na modalidade presencial e/ou no ensino a distância

O advento das novas tecnologias e a dinamicidade das mudanças que estas provocam, impactam diretamente em vários aspectos da sociedade, dentre estes, na educação. Novas metodologias e mudanças no processo de ensino-aprendizagem tornam-se práticas cada vez mais frequentes neste campo. O elemento basilar desta nova constituição é o docente, capaz de transformar a utilização desses recursos em ferramentas que favoreçam o processo educativo. Essa readequação do comportamento exigida por essas constantes mudanças é orientada pelos valores pessoais dos sujeitos que vivenciam a situação. Os valores são idealizados como critérios que interferem diretamente nas atitudes, preferências e até mesmo no comportamento humano, influenciando no modo como o indivíduo interpreta as suas próprias atitudes e as dos outros, inclusive no âmbito profissional. Dessa forma, o objetivo geral da presente pesquisa é analisar as relações entre o perfil de uso da tecnologia e os valores dos docentes da UFRN Universidade Federal do Rio Grande do Norte, baseado na escala de valores de Schwartz. Para isso foram utilizados os tipos motivacionais que compõem a teoria de valores de Schwartz, através de questionário aplicado junto aos docentes. Trata-se de uma pesquisa de enfoque analítico quantitativo que utiliza um questionário da escala de valores desenvolvida por Schwartz et al. (2001) conhecida como PVQ (Portrait Values Questionnaire). A pesquisa foi desenvolvida a partir de uma amostra de 200 docentes entre atuantes da modalidade presencial e/ou na modalidade de ensino a distância. A estratégia de análise dos dados utilizou técnicas de estatística descritiva, análise de gráficos, análise das frequências relativas e a técnica estatística MANOVA (Análise Multivariada de Variância). Os resultados apontaram que os docentes utilizam moderadamente os recursos tecnológicos avaliados nesta pesquisa, como ferramenta de apoio pedagógico. Com relação ao perfil de valores, os docentes apresentaram prioridade entre os tipos motivacionais Autodeterminação, Benevolência e Universalismo, enquanto os menos priorizados foram os de Tradição, Realização e Poder, respectivamente. Contudo, não foram identificadas relações significativas entre o perfil de valores e o perfil de uso da tecnologia entre os docentes estudados nesta pesquisa

O projeto de arquitetura de espaços temporários com o uso de sistema construtivo remontável: um estudo exploratório

The purpose of this research is to study the portable or reassemblable architectures, which, different from conventional architecture (whose designs are of permanent buildings), corresponds to the designing of spaces with temporary purposes. The focus of the study is the architectural design of spaces that are produced from building systems that can to be moved to different places (process of assembly / disassembly / reassembly) in order to identify the types of spaces generated and the processes used in their design / projecting. The aim is to investigate relationships between the initial project conceived based on a Reassemblable Construction System (RCS) and its application in the architectural design of professionals and students in order to contribute to the understanding of the specificities of this type of design activity. To this end it was developed the exploratory research based on multimedia methods, which includes: documentary analysis, technical visits, interviews, surveys, academic exercise and documentation by images. Although the study is not conclusive, the results indicate significant differences between the point of view of the RCS´s designers and its users (architects and architecture students) since the users demonstrated to have some difficulty to access the features provided for the first group, in particular the students. It is also demonstrated that the use of RCSs seems to change the appreciation / hierarchization of the conditions of project design, since, unlike what happens in traditional architectural design, the designers who use them seem to be more concerned with constructive issues, especially the structural elements (support and covering), instead of functionality, aesthetics and even physical characteristics of the site

Para que servem hoje nossas cozinhas? :uma análise de uso das cozinhas do Plano 100 (Natal-RN)

This work investigates the using of kitchens of the apartments of PLANO 100 in Natal-RN, through one method s set of the functional and behavior evaluation. The theme was selected through of the emergence of the many questions that sought to understand what manners how individuals relates to the constructed space, what was the possible changes caused by these relation, also verifying how this space interferes in a daily life of theirs users. This research to search answers what to improve of the study s object and in futures production s architectonic too. The used approach combined an overview of new kinds of familiar arrangements and the evolution process of the brazilian s kitchens within social context of Brazil, with APO (Post-Occupation Evaluation), techniques through a physical space survey, questionnaires and interviews with users. Beyond to APO s implements were applied behavior setting s techniques too, what presented the most knowledge about to satisfactions levels pointed by the users

Adição de cascalho de perfuração da bacia potiguar em argilas para uso em materiais cerâmicos: influência da concentração e temperatura de queima.

One of waste produced on large scale during the well drilling is the gravel drilling. There are techniques for the treatment of the same, but there isn t consensus on what are the best in terms of economic and environmental. One alternative for disposal of this waste and objective of this paper is the incorporation and immobilization of gravel clay matrix to assess their technological properties. The Raw Materials used were characterized by the following techniques: Chemical Analysis by X-ray fluorescence (XRF), mineralogical analysis by X-ray Diffraction (XRD), Grain Size Analysis (FA) and Thermal Analysis by Thermogravimetry (TG) and thermodiferential (DTA). After characterizing, samples were formulated in the following percentages: 0, 5, 10, 15, 25, 50, 75, 100% (weight) of gravel drilling, then the pieces were pressed, dried (110 ° C) and sintered at temperatures of 850, 950 and 1050 ° C. After sintering, samples were tested for water absorption, linear shrinkage, flexural strength, porosity, density, XRD and test color. The results concluded that the incorporation of gravel drilling is a viable possibility for solid masonry bricks and ceramic blocks manufacture at concentrations and firing temperature described here. Residue incorporation reduces an environmental problem, the cost of raw materials for manufacture of ceramic products